Latest / FE exam in the car / FE Exam: Centroids and Moments of Inertia — How to Find the Center of Any Shape
Transcript
- 0:00Speaker 1: Well, the podcast is doing so well, we decided to
- 0:02Speaker 1: give you another episode, and hopefully you'll enjoy it. Today
- 0:06Speaker 1: we're going to be talking about centroids. So you're designing
- 0:09Speaker 1: a steel beam, right, to support a floor. You know
- 0:12Speaker 1: the material, the dimensions, and the loads, but two questions remain.
- 0:15Speaker 1: Where is the center of the beam's cross-section, and how
- 0:17Speaker 1: is its area spread around that center? Those are centroids
- 0:22Speaker 1: and moments of inertia. The centroid is the geometric center
- 0:26Speaker 1: of an area for an object with uniform density and
- 0:28Speaker 1: matches the center of mass. A rectangle's centroid sits at
- 0:32Speaker 1: half its width and half its height. A triangle's centroid
- 0:36Speaker 1: sits one-third of the height up from its base. For
- 0:39Speaker 1: complicated shapes, we use composites, meaning we break the shape
- 0:43Speaker 1: into simple pieces. Picture a T-shaped cross-section. The vertical piece,
- 0:48Speaker 1: called the stem, is 2 cm wide and 8 cm tall.
- 0:52Speaker 1: The horizontal piece on top, called the flange, is 10
- 0:55Speaker 1: cm wide and 2 cm thick. centered over the stem.
- 1:00Speaker 1: We'll measure everything from the bottom. The stem's area is
- 1:03Speaker 1: 16 square centimeters and its centroid is 4 centimeters up.
- 1:07Speaker 1: The flange's area is 20 square centimeters and its centroid
- 1:10Speaker 1: is 9 centimeters up. Now you multiply each area by
- 1:14Speaker 1: its centroid height. So 16 times 4 is 64. 20
- 1:17Speaker 1: times 9 is 180. You add them together to get 244.
- 1:26Speaker 1: Then you divide by the total area, 36 square centimeters,
- 1:30Speaker 1: and the centroid lands about 6.78 centimeters above the bottom.
- 1:37Speaker 1: Just pull up toward the flange because that's where most
- 1:40Speaker 1: of the area sits. Now the area moment of inertia.
- 1:44Speaker 1: The centroid tells you where the area is. The moment
- 1:47Speaker 1: of inertia tells you how far that area is spread
- 1:49Speaker 1: out from an axis. And that spread controls how much
- 1:53Speaker 1: a beam and how much stress it carries. For a
- 1:56Speaker 1: rectangular about its own center line, the formula is BH
- 2:01Speaker 1: cubed over 12. Spoken as BH cubed over 12. That
- 2:07Speaker 1: means the base times the height times the height times
- 2:11Speaker 1: the height divided by 12. Because the height is cubed,
- 2:15Speaker 1: depth matters enormously. Double a beam's depth and its stiffness
- 2:19Speaker 1: goes up 8 times. For composite shapes, we use the
- 2:23Speaker 1: parallel axis theorem. I equals I bar plus AD squared.
- 2:31Speaker 1: In plain words, each piece's total equals its own moment
- 2:34Speaker 1: of inertia plus its area times the square of its
- 2:36Speaker 1: distance to the overall centroid. Let's finish our T. Remember,
- 2:40Speaker 1: the stem's own moment of inertia is 2 times 8
- 2:43Speaker 1: cubed over 12, which is about 85.3. The stem's center
- 2:48Speaker 1: sits about 2.78 centimeters below the overall centroid. We add
- 2:54Speaker 1: 16 times 2.78 squared, which is about 123.5. The stem
- 2:58Speaker 1: contributes about 208.8. The flange's own moment of inertia is
- 3:00Speaker 1: 10 times 2 cubed over 12, which is about 6.7.
- 3:02Speaker 1: Its center sits about 2.2 centimeters above the overall centroid,
- 3:06Speaker 1: so we add 20 times 2.2 2 squared, which is
- 3:22Speaker 1: about 98.8. The flange contributes about 105.5. Add the two pieces,
- 3:29Speaker 1: and the total is about 314 centimeters to the fourth power.
- 3:34Speaker 1: Notice that the transfer terms, the A, D squared parts,
- 3:37Speaker 1: are bigger than the pieces' own moments of inertia. That's
- 3:40Speaker 1: actually typical of forgetting them as the single most common
- 3:43Speaker 1: mistake on the exam. A few more traps for the exam.
- 3:49Speaker 1: The area moment of inertia is measured in length to
- 3:52Speaker 1: the fourth power. The mass moment of inertia used in
- 3:54Speaker 1: dynamics is measured in bass times length squared. So don't
- 3:59Speaker 1: mix those up. So the area moment is different than
- 4:03Speaker 1: the mass moment. Always transfer to the whole shape centroid,
- 4:06Speaker 1: not to the bottom of each piece. And in BH
- 4:09Speaker 1: cubed over 12... The base is the side that runs
- 4:16Speaker 1: parallel to the bending axis. Three steps for exam day. First,
- 4:20Speaker 1: split the shape into simple areas. Second, find the centroid
- 4:24Speaker 1: with an area weighted average. And third, add up each
- 4:27Speaker 1: piece's own moment of inertia plus its AD squared.