Latest / Red Talks / Episode 17: Predictive Maintenance: Vibration Analysis and Complementary Technologies
Transcript
- 0:09SPEAKER_01: What is vibration analysis in a nutshell?
- 0:14SPEAKER_00: Reliability has uh a number of condition monitoring technologies, maybe thermography.
- 0:20SPEAKER_00: Everybody understands that's just temperature and a picture of temperature, you know, or you can just take a uh a little gun, ray gun out and you know hit it and it'll give you a temperature on the thing.
- 0:30SPEAKER_00: And that's tracking just one value, just temperature.
- 0:34SPEAKER_00: So it's got essentially no phase information with it at all.
- 0:37SPEAKER_00: In other words, no direction.
- 0:39SPEAKER_00: It's just a value, okay?
- 0:41SPEAKER_00: But if we add a dynamic capability to that, uh when we make a measurement, that becomes a vector instead of a scalar, okay, to use math terms for it.
- 0:54SPEAKER_00: So when you add the direction of the component that you're monitoring, and vibration is a dynamic measurement, it has that phase information attached to it as well.
- 1:06SPEAKER_00: So, complicated way of saying that we can look at the value of the vibration and how large it is, but we can also see its phase information to see how the machine is moving from one measurement location to another, is that phase different than it should be?
- 1:25SPEAKER_00: Let's say it's out of balance.
- 1:26SPEAKER_00: So we expect a big heavy spot to roll by the sensor in the horizontal direction first, and then 90 degrees later in the rotation to move by the vertical.
- 1:35SPEAKER_00: Okay?
- 1:36SPEAKER_00: But if that's not the relationship, then something else is wrong.
- 1:40SPEAKER_00: Okay?
- 1:40SPEAKER_00: So you have two or three different values in vibration data that you can analyze to learn how bad the vibration is and what its mode kind of is in terms of the failure you're doing.
- 1:55SPEAKER_00: So certain things like um, you know, impacting will mean maybe a loose base, or you have a hold down bolt that's come loose and it's the foot's just slamming down there as it rotates, right?
- 2:06SPEAKER_00: So vibration analysis allows us to look at the signature, is what we call it, the amplitude and its phase information from a machine, and allows us to determine how severe it is, how fast it's going to failure, okay, which is the key portion there, because you can trend these over time, and they will increase in amplitude, and then we can tell if it's truly maybe an imbalance or if it's really just a shaft that's misaligned.
- 2:34SPEAKER_00: They look very similar in amplitude, but the story is told in the face.
- 2:39SPEAKER_00: So we when we say vibration analysis, we're actually looking at two components of the same signal.
- 2:44SPEAKER_00: Okay, so that's that's what vibration analysis typically is.
- 2:48SPEAKER_00: So we can look at things like bearings, are they going bad?
- 2:52SPEAKER_00: We can look at shafts, are they going bad?
- 2:54SPEAKER_00: And you can do a lot of mechanical analysis and keep a machine from going to just complete and total failure and wrecking itself, and you can replace the bearings well before you know they do that, before they wreck.
- 3:07SPEAKER_01: So what are some complementary technologies to vibration analysis?
- 3:17SPEAKER_00: Lubrication.
- 3:18SPEAKER_00: Very, very important.
- 3:19SPEAKER_00: You can get stuff like percentage water in your oil, for example.
- 3:23SPEAKER_00: You can get particulate counts in that.
- 3:26SPEAKER_00: So there's a number of things in lubrication that are very complementary to vibration.
- 3:32SPEAKER_00: You should see the same story going on across both of those.
- 3:36SPEAKER_00: Another one would be ultrasonics, so you're listening with a microphone that's capturing ultrasonic or above our hearing type of screeching noises that come from a bearing going bad, for example.
- 3:48SPEAKER_00: And or maybe it's air leaks and things like that.
- 3:50SPEAKER_00: So those are two very complementary, uh, almost very similar type of uh information delivery on the condition of the machine from really all three of those technologies.
- 4:01SPEAKER_00: So, yes, they're very complementary.
- 4:02SPEAKER_00: Some of the old hands, especially, and they may be a little biased, I'll be first to say, uh, in the vibration world tell us that the vibration uh signal really gives us the most bang for our buck because it's a dynamic signal, in going in and and uh looking at that.
- 4:19SPEAKER_00: Uh ultrasonic signal is typically an amplitude, although they have recently started looking at some of the frequency content in uh in those ultrasonic measurements.
- 4:29SPEAKER_00: So but typically is just reported as a decibel amplitude uh in uh ultrasonics, okay?
- 4:35SPEAKER_00: So it's been a one-value component, whereas vibration again gives you several components, like I just said, the phase and amplitude information is usually uh used and preserved depending on how you take the measurement, really, but that's that's what they do.
- 4:49SPEAKER_00: So, yes, uh very complementary technologies, and uh all of those should and temperature uh should uh typically be used by a plant, and many of them have multiple programs uh like that in their condition monitoring uh portfolio of technologies to tell them what's going on in a in a machine.
- 5:11SPEAKER_01: Red Talks features voices driving safety, reliability, and innovation forward in the industrial world.
- 5:18SPEAKER_01: If your work challenges the status quo, we'd like to hear from you.
- 5:21SPEAKER_01: Learn more at redtalk.comslashabout.